![chirp programming cable chirp programming cable](https://i.ytimg.com/vi/BR6vv499vGQ/maxresdefault.jpg)
#Chirp programming cable plus
Yaesu FT-4X is a very interesting handheld radio that is not very expensive (~ £65) and I believe is a good starting point compared to my previous Baofeng UV-5R Plus radio. You can buy either the FT-8900R and the Marvogo USB programming cable from post was cloned to my other website dedicated to amateur radio (ham radio) M0TTZ.UK Prologue I can choose which bank to scan so I it’s pretty versatile.įor my review of the Marvogo USB Programming Cable I use, check out my review article at /Marvogo-USB-Programming-Cable-Review The frequencies, offsets and tone requirements were all added in just seconds.Īfterwards, I checked each of the repeaters early in the morning while propagation was still good and deleted the ones I couldn’t hit.īecause it has so many memories available, I also included all the FRS, GMRS, MURS, and WX frequencies so I can monitor any of them as desired.īecause this radio banks the memories so I can scan certain groups, I can program the local public service frequencies into one section and the ham into another.
![chirp programming cable chirp programming cable](https://geek-ff8b.kxcdn.com/wp-content/uploads/2015/02/BTECH-PC03-FTDI-probramming-cable-700x502.jpg)
It has a proximity setting, so I set it to 75 miles and downloaded all repeaters. One of the best features I like about Chirp is it’s ability to download frequencies from. I don’t have a floppy or a CD drive, so I can’t use it.Ĭhirp doesn’t allow you to change any specialty frequencies such as the Hyper-Memories and range frequencies, but those can easily be set by hand on the radio.
#Chirp programming cable software
I have a copy of ADMS software for programming the Yaesus, but it is so old, it is on a floppy. It works much more quickly on my Kenwood TM-281 and Baofeng radios which only have up to 127 memory locations, but the 8900 has 800 memory locations, so it takes 5 to 8 times as long to transfer. My desktop (not the fastest computer in the world) takes 3 to 5 minutes to transfer to and from the Yaesu. On they 8900, press V/M immediately after. You only have about 1/2 to 1 second to press both buttons The first time you use a radio with Chirp, you have to have Chirp download from the radio.
![chirp programming cable chirp programming cable](https://i.ebayimg.com/images/g/bFcAAOSwU1dfZCD0/s-l400.jpg)
(the small square button in the middle).Rotate the right frequency knob until you see.
![chirp programming cable chirp programming cable](https://arcanecode.files.wordpress.com/2019/04/image_thumb.png)
#Chirp programming cable how to
Then I talked to another ham on one of the local repeaters who corrected me in how to use it. When I received it, the new cable did the same thing. I returned the cable as defective and ordered another one. The radio immediately went into transmit until I turned it off again! So, like I do with my Kenwood and Baofeng, I plugged in the cable and turned on the radio…. When I first ordered the cable to program the Yaesu FT-8900R, I didn’t realize just how to work it. I ordered the cable for the FT-8900 and learned how to program the radio using the Chirp software. When I looked at all the radio options, I saw it also programmed the three other radios that I also have, The Kenwood TM-281, Yaesu 857, and FT-8900. When I received my Baofeng UV-5R, I also received a programming cable so I downloaded the free CHIRP software for programming the HT.